|
 |
MANUFACTURER'S NAME:
|
NATIONAL COATINGS CORPORATION
1201 CALLE SUERTE
CAMARILLO, CA 93012
www.nationalcoatings.com |
EMERGENCY TELEPHONE: |
800-423-9557 |
DATE OF LAST REVISION: |
11/9/04 |
SECTION I - PRODUCT IDENTIFICATION
| PRODUCT NUMBER: |
A130 |
| PRODUCT NAME: |
PVC Primer |
| PRODUCT CLASS: |
Acrylic Primer |
SECTION II - HAZARDOUS INGREDIENTS
| PRODUCT |
CAS REG NO |
WEIGHT (%) |
| Tris(2-butoxyethyl)phosphate |
78-51-3 |
1.5 Max |
| Dibutyl Phalate |
84-74-2 |
3.0 Max |
| Diethylene glycol monobutyl ether |
112-34-5 |
3.0 Max |
SECTION III - PHYSICAL/CHEMICAL CHARACTERISTICS
| APPEARANCE: |
Milky white liquid |
EVAPORATION RATE: |
Slower than ether |
| BOILING POINT: |
212°F |
SPECIFIC GRAVITY: |
(water=1) 1.0-1.2 |
| VAPOR DENSITY: |
Less than air |
% VOLATILE BY VOLUME: |
83% |
SECTION IV - REACTIVITY DATA
| STABILITY: |
Stable |
| HAZARDOUS POLYMERIZATION: |
Will not occur |
| HAZARDOUS DECOMPOSITION PRODUCTS: |
Acrylic monomers |
| INCOMPATIBILITY: |
None reasonably foreseeable |
SECTION V - FIRE & EXPLOSION HAZARD DATA
| FLAMABILITY CLASSIFICATION: |
Not DOT Regulated Flash Point - Non combustible LEL - N/A
|
| EXTINGUISHING MEDIA: |
N/A |
| UNUSUAL FIRE & EXPLOSIONS HAZARD: |
Material can splatter above 212°F
Polymer film can burn. |
| SPECIAL FIREFIGHTING PROCEDURES: |
For fires involving this material, do not enter any enclosed or confined space without proper protective gear, including self-contained breathing apparatus to protect against the hazardous effects of the normal products of combustion or oxygen deficiency. |
SECTION VI - SAFE HANDLING & USE INFORMATION
| RESPIRATORY PROTECTION: |
Wear suitable respirator (MSHA/NIOSH approved or equivalent) where exposure limits are exceeded. |
| VENTILATION: |
Mechanical local exhaust ventilation at point of containment release. |
| PROTECTIVE GLOVES: |
Impervious for prolonged or repeated contact. |
| EYE PROTECTION: |
Chemical splash goggles (ANSI Z-87.1 or approved equivalent). |
SECTION VII - HEALTH HAZARD DATA
EFFECTS OF OVER EXPOSURE:
- INHALATION: Vapor or mist can cause irritation of the nose, throat and lungs.
- EYE & SKIN CONTACT: Slightly irritating to eyes with direct contact.
- Skin Exposure: Irritating to skin with repeated or prolonged exposure.
EMERGENCY & FIRST AID PROCEDURES
- INHALATION: Move subject to fresh air.
- EYE & SKIN CONTACT: Flush eyes with large amounts of water for at least 15 minutes. See a physician if irritation persists. Wash affected skin areas with soap and water.
- INGESTION: If swallowed, dilute by giving two glasses of water to drink. CALL A PHYSICIAN IMMEDIATELY.
SECTION VIII - SPILL OR LEAK PROCEDURES
| STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: |
Keep spectators away. Floor may be slippery, use care to avoid falling. Scoop or shovel solid material into a suitable container for recovery or disposal. Keep spills out of municipal sewers and open bodies of water. |
| WASTE DISPOSAL METHODS: |
Disposal should be in accordance with Federal, state, and local regulations |
SECTION IX - SPECIAL PRECAUTIONS
| PRECAUTIONS TO BE TAKEN IN HANDLING & STORAGE: |
Keep from freezing. |
| OTHER PRECAUTIONS: |
None |
| UNUSUAL FIRE & EXPLOSIONS HAZARD: |
Material can splatter above 212°F
Polymer film can burn. |
|
| |
|
|
|
